Hi there, I’ve tried sending midi messages over usb with an Ampero control to the profile player with no success, connecting ampero usb to usb A on Player. If I use a midi to usb host cable everything works. Channels are ok (1 for Ampero,Omni on Kemper), I tried different usb cables. What could be the problem? Any advice? |
Profile Player and Ampero Control
-
00diablo00 -
December 30, 2023 at 11:36 AM -
Thread is marked as Resolved.
-
-
Hi I have no answer to your question, sorry, but could you tell me, how to dial in the channel on the kemper player?
-
If you want to control multiple devices independently, you can set a specific channel in System Settings. Now, the Player will only
process messages received on that channel.
-
Hi Bakersounds
I really have not found the possibility to choose the midi channel in the System Settings. not to hijack 00diablo00 thread, I will open a new one
-
I've had the info from the manual under "Midi" --> Midi Global Channel. Sorry i can't say anything more in detail.
-
Hi I have no answer to your question, sorry, but could you tell me, how to dial in the channel on the kemper player?
tricky. The manual speaks about a midi section I simply don’t have in my rig manager
-
it does not exist as far as I know I spent hours trying !
-
I don’t know for sure but suspect this is a feature which hasn’t been implemented yet like the combination pedals (sorry I forget the correct term for this) which are close enough to release to mentioned in the manual but have been held up for some reason.
-
Following. I intend to control mine from HX FX (when it arrives…) and hope to also simply use a USB cable…
-
- Official Post
The parameter "MIDI Global Channel" is planned to be added in the next OS and Rig Manager updates. So far the Player works in "Omni" mode constantly. So if you are sending MIDI comands on various channels (1-16), the Player will execute all of these.
That's all that's missing: There is no "MIDI section" missing. If your Player doesn't execute MIDI comands send from the USB socket of your Ampero Control, it's not because of that missing MIDI Global Channel parameter. Others succeeded using a Keith McMillan Softstep with the Player connected via USB cable.
-
I also have troubles sending midi messages with the ampero control - no way to get it work and tried for hours now. I will order now the Keith McMillen
-
WELL I got mine working using the disaster area dpc-5 gen 3 not perfect but it's getting there .
-
- Official Post
I just made a simple test: I used a MIDI to USB adapter, which has a USB-A plug on one side and two 5-pin MIDI plugs on the other side. I plugged its MIDI plugs into a PROFILER Rack and activated "UI to MIDI" there.
The Player follows
- dialing GAIN at the Rack
- switching effect module DLY on and off at the panel of the Rack
- navigating through Performances at the Rack e.g. loading Performance 4 Slot 3 loads Bank 4 Slot 3 at the Player.
At the same time I can send MIDI comands from freeware MIDI OX on my PC into the USB-B socket of the Player via the same cable I use for Rig Manager. These are processed, too.
Conclusion: There is no evidence that the Player as a receiving MIDI device doesn't work as expected and documented. If you are experiencing issues, test with another sending device as a reference. MIDI OX is freeware and a good choice.
-
00diablo00 Did you route PC data to the USB output of the Ampero?
There is a dedicated setting:
Output To lets you decide how MIDI message will be sent. You can send it via either Bluetooth, USB jack, MIDI OUT jack or any combinations.
As the USB to MIDI cable worked, I assume that the ampero is set to send to MIDI out only.
-
Good morning,
I am facing the same issue
Ampero Control was setup to send signal via usb
I tried it with this cables but none worked
Lindy USB 2.0 Typ A/B 1mLindy USB 2.0 Typ A/B 1m; Typ A/B Kabel; Anthra Line; unterstützte Bandbreite: 480Mbit/s; PVC-Gehäuse mit vergoldeten Kontakten und nickelbeschichteten…www.thomann.deSecond test was done to send the midi signal through the Tonex midi out to the usb port
Thomann Midi USB 1x1Thomann Midi USB 1x1, Midi-Interface 1x MIDI-In 1x MIDI Out, Gesamtlänge: ca. 2m, kompatibel mit Windows 7/8.1/10 (USB 2 und 3) sowie Mac OSXwww.thomann.de -
WELL I got mine working using the disaster area dpc-5 gen 3 not perfect but it's getting there .
good to hear that this works (did you use USB only for this?)
-
Good morning,
I am facing the same issue
Ampero Control was setup to send signal via usb
I tried it with this cables but none worked
https://www.thomann.de/de/lindy_usb_2.0_typ_a_b_1m.htm
Second test was done to send the midi signal through the Tonex midi out to the usb port
you say: 'none' worked... so the 2nd try was:
XXX -> MIDI -> USB -> PLAYER ?
and this didn't work? how/what did you test?
(because that is basically the same scenario Burkhard and others describes and tested successfully)
-
good to hear that this works (did you use USB only for this?)
OK I AM USING DPC-5 GEN 3 FROM DISASTER AREA , SO IT CONNECTED ONLY THE USB ( MINI USB TO USB A ) IT IS NOT SMOOTH SINCE THE KKP IS IN OMNI
-
MIDI channel selection will be available in an upcoming update
-
you say: 'none' worked... so the 2nd try was:
XXX -> MIDI -> USB -> PLAYER ?
and this didn't work? how/what did you test?
(because that is basically the same scenario Burkhard and others describes and tested successfully)
I will test another cable on monday or tuesday
Explaining more in detail :
i have an dual modeler setup
ToneX + Kemper Profile Player
At the end everything should be done with the Midi Switcher exept the "normal pedals" i like and can replace to my taste and purchases
-