since a few days i need to manually enter date and time when starting.
i upgraded tot 8.2.2.28378 dated may 20th same problem occurs
regards Lars
since a few days i need to manually enter date and time when starting.
i upgraded tot 8.2.2.28378 dated may 20th same problem occurs
regards Lars
Backup battery ?
since a few days i need to manually enter date and time when starting.
i upgraded tot 8.2.2.28378 dated may 20th same problem occurs
regards Lars
Contact support please.
Aha! So I'm not the only one. Happened on my toaster as well.
I saw this for the first time maybe 1 week ago on my Toaster that is 7 or 8 years old. I feared the worst.
I searched the forum for time and date issues. One of the mods wrote back and said that, if this only happens when connected to rig manger, I should go into the setup menu and check the clock was actually running - if it is then 'no problem'. In my case it was running.
I am hoping for luck here and will curse it now but, so far, no repeat of this.
Sorry, I just searched for the thread again but can't see it.... Hope yours turns out well.
Same issue with a brand new kemper stage. Happened on day one.
Updated the software, but issue wasn’t fixed.
I set up the date manually, but I get the same error after turning off/on
Even if the date/date is synced and updated when connecting to rig manager, the error continued to occur after turning the unit off/on.
I have seen the Clock setup error before, but it was only when I booted my toaster with the USB Plugged in. I am just now upgrading to 8.2.2. I will report and see if I see this Clock issue. I always upgrade off of my USB Stick and never upgrade from Rig manager. I just don't trust upgrading from RM.
Ok I just upgraded my Toaster to 8.2.2 have had no Clock Issues. I guess it is kind of good news, and I did power cycle my toaster a few times. I am not hooked via USB to Rig Manager. I highly recommend not to be connected to USB when booting your Kemper up, or you will from time to time see this Clock error.
same problem.....whats the answer....
same problem.....whats the answer....
Not sure. I entered the date/time back in and the issue has not come back so far.
If you experience this only once after a start up and while Rig Manager is connected, you can ignore the message.
If this happens after every restart, please contact KEMPER support.
(Edit) - Removing my previous observations, as this Stage unit is still functionally broken (getting time clock error messages shown in this thread) - however the troubleshooting variables I listed are now showing completely different outcomes hours later and do not help with clarification for a forum reader or Moderator. Its all over the place - Kemper Support ticket submitted.
Just opened a ticket. Only happens if I power down, remove the power cable, then power back up.
If I power down/up with power cable in it doesn't happen.
Just opened a ticket. Only happens if I power down, remove the power cable, then power back up.
If I power down/up with power cable in it doesn't happen.
dmatthews - mine was doing as yours is at first, but now its doing it both ways variably. No rhyme or reason, just one constant now, its returning 100% of the time. I submitted two tickets, no response yet. Thank you for contributing in with this one. RA
dmatthews - mine was doing as yours is at first, but now its doing it both ways variably. No rhyme or reason, just one constant now, its returning 100% of the time. I submitted two tickets, no response yet. Thank you for contributing in with this one. RA
I have great confidence that this will be resolved in the next release or beta.
I just receive my profiler Stage from Kemper and what a disappointment !!!
The machine is on an older version of operating system but it's not a problem. At first I put on the profiler alone and when I put it on I have this beautiful window :
So I have same thing than before !!!
I open an older version of Rig manager (3.0.145) and I put on the profiler and same thing.
It's not serious ! Please stop the geeks ...
Just a piece of shit ...
Did some experiments
This happens to me only if I disengage the power cable and reboot.
Doesn't matter if USB or Midi is plugged in.
I am being told that I'll need to send my toaster for repair, and that others having this issue is a coincidence.
Could be... I bought mine used locally. Just seems well... interestingly coincidental. I've been on this forum for years now and not seen this issue until now.
Maybe the battery backed up RTC circuit with empty battery. Those are relied for time when mains power is removed.
Maybe the battery backed up RTC circuit with empty battery. Those are relied for time when mains power is removed.
Yes, that is what support is saying for my toaster.