mix going to 100%
I own the Kemper since 2012 and therefore own a lot of "old" profiles too. If I preload those old profiles via RigManager and part of the profile is reverb then the reverb mix seems to be always on 100%.
5.7.2.14219: Any known issues?
-
Chris Duncan -
March 9, 2019 at 5:31 AM -
Thread is Resolved
-
-
I own the Kemper since 2012 and therefore own a lot of "old" profiles too. If I preload those old profiles via RigManager and part of the profile is reverb then the reverb mix seems to be always on 100%.
What about if you load a reverb preset; does that have 100% too?
-
What about if you load a reverb preset; does that have 100% too?
I must check this. But there are imho two things to note: It's annoying if you want to prelisten an old profile and always have to load another reverb preset first (apart from the possibilty that you maybe would like the preloaded reverb [if it would be loaded as it was intended] and like to keep it). Second thing is that a new reverb preset alters the original profile which makes it hard to judge.
-
I must check this. But there are imho two things to note: It's annoying if you want to prelisten an old profile and always have to load another reverb preset first (apart from the possibilty that you maybe would like the preloaded reverb [if it would be loaded as it was intended] and like to keep it). Second thing is that a new reverb preset alters the original profile which makes it hard to judge.
This was assuming you had a favourite reverb sound saved for general use.
-
Ah, I see but I haven't. I like to get inspired by settings from other users.
-
I own the Kemper since 2012 and therefore own a lot of "old" profiles too. If I preload those old profiles via RigManager and part of the profile is reverb then the reverb mix seems to be always on 100%.
Not experiencing that issue. What does Kemper support say?
-
alwainwright : I don't know, I haven't contacted the support. It's a not very important issue to me, I just wanted to point out a possible bug.
-
Glad to see I'm not the only scaredy cat in the room.
You are not the only scaredy cat in the room! I'm finally updating now. Fingers crossed.
-
Not experiencing that issue. What does Kemper support say?
this is a bug that somehow slipped through the betatest. Our developers are already aware of it.
-
this is a bug that somehow slipped through the betatest. Our developers are already aware of it.
That's great! How about the elimination of the morphing parameters? Have you identified that one too? TIA
-
this is a bug that somehow slipped through the betatest. Our developers are already aware of it.
Thank you for chiming in. For those that are experiencing this issue will be happy to hear that Kemper is aware of this bug.
-
Just thought I'd share an issue I had in case anyone else gets affected, Kemper support knows about this and I believe it's being addressed but; the "Quad Chromatic" reverb setting that I have (which I got with Liam Thompsons awesome rigs of RE) now make my Kemper squeal it's head off after the update. I have had to disengage it from a few rigs or avoid them altogether. Even with guitar volume off the profiles start to softly squeal and then the volume goes up. I must stress Kemper has acknowledged it, but just in case someone else experiences it hopefully will be resolved in a update fix. Has anyone else actually experienced this?
-
Just thought I'd share an issue I had in case anyone else gets affected, Kemper support knows about this and I believe it's being addressed but; the "Quad Chromatic" reverb setting that I have (which I got with Liam Thompsons awesome rigs of RE) now make my Kemper squeal it's head off after the update. I have had to disengage it from a few rigs or avoid them altogether. Even with guitar volume off the profiles start to softly squeal and then the volume goes up. I must stress Kemper has acknowledged it, but just in case someone else experiences it hopefully will be resolved in a update fix. Has anyone else actually experienced this?
the fix for this will be in the next update
-
I own the Kemper since 2012 and therefore own a lot of "old" profiles too. If I preload those old profiles via RigManager and part of the profile is reverb then the reverb mix seems to be always o
I have the same issue or similar. After the newest update, most of my rigs have the Legacy reverb at a very high mix rate, all with the Legacy reverb attached. I know for a fact that all of these rigs did not have the Legacy reverb before the update. Seems like this is an issue as well? Anyone else with this issue?
-
I have the same issue or similar. After the newest update, most of my rigs have the Legacy reverb at a very high mix rate, all with the Legacy reverb attached. I know for a fact that all of these rigs did not have the Legacy reverb before the update. Seems like this is an issue as well? Anyone else with this issue?
the legacy reverb bundles all the previous reverb types to one effect type and automatically converts the old settings. The bug that the mix and rev/delay balance was off for rigs that were stored in a version older than 5.0 is fixed in the next update. If you store those rigs in 5.5.2 the reverbs should sound the same.
-
hjscheffler, thanks for the insight. I figured you guys were aware of the issues and were working on a maintenance release, and that was part of what I was hoping for with this thread.
I just noticed this thread 5.7.4.14373 Public Beta - is this the release you were referring to?
yes-that is the one
-
yes-that is the one
Does that release also fix the disabled morphing?
-
the legacy reverb bundles all the previous reverb types to one effect type and automatically converts the old settings. The bug that the mix and rev/delay balance was off for rigs that were stored in a version older than 5.0 is fixed in the next update. If you store those rigs in 5.5.2 the reverbs should sound the same.
That's correct. My reverbs in 5.5.2 were fine until I updated to the new OS.
-
Hello! I think i found a small bug here. When use the "Browse" button on any of the 4 stomps slots, the lcd color does not change to match up to the stomps type currently being scrolled, it stays the default light green. The lcd color does instead change when using the "Type" button on any of the 4 stomps slots or when using either the "Browse" of the "Type" button on any of the 4 effects slots. Anyone else experience this with 5.7.2?