Same thing here!
Same for me too.
Same thing here!
Same for me too.
Sorry if this has been touched on already but I just loaded 4.0 and was working with some of my rigs and noticed that the volume or level control is missing now on the Cabinet module. To be honest it may have been in 3.3 as well but didn't notice it. Anybody else see this?
Dan
yes it's gone according to the manual
There's discussion in this topic about it. It's gone now (merged to amp volume), because cabinet volume didn't really make sense.
Ugh...here's another. When using a delay as the morph stage and then switching to a different slot on the remote, that new slot seems to pick up more of the previous delay and not what it should be set at until I go to another slot and then back.
You should inform Kemper support about these issues.
You should inform Kemper support about these issues.
Already sent in a ticket with the first issue but there was no way to attach the backup. waiting on a reply.
and another...when powering up the Kemper and then going to performance mode...it defaults to a performance that isn't even supposed to be there. I have to bank down or up and then hit some buttons in order for it to find the correctly named performances. Actually, I have to really scrool through banks and then back for it to even find the performance in the correct bank. It shows as new performance even though there is a named performance there. Takes a few times of going through banks and slots to get it right.
I am confused.
Yesterday there was page with external pedal setting.
I could choose
Single or dual switch.
Tip and ring .
Function for Looper start ,stop or stomp etc.....
Today page is gone.:-) !!!???
Excuse my English.!
OK - my first 4.0 issue (I'm sending a support ticket); every time I turn the KPA on the "morph link" check box is empty and I have to re-link (I'm using Morph to Wah). Anyone experiencing this?
My brain's morphed from reading this thread - into what, I don't know.
I think I'll leave the beta testing to you guys; you all seem to be doing a bang (crash?)-up job.
Carry on.
Hi Everyone!
I moved to 4.0 last night. Not noticed all the performance issues but scrolling was a bit wierd as I recall. I did notice that on Rigs where I need to use my expression pedal for Wah, the Wah didn't sound as smooth as usual, more of a staged incremental shifting of tone.
Has anyone else experienced this?
I reduced the rise and fall times to zero and this (I think) helped a bit.
Cheers
Pre-Amp
A service ticket is being opened on the issue I posted earlier in the thread as they were able to reproduce it.
Same for me too.
LOL. There are a million and one things I can understand slipping through the "Alpha" test phase. This particular issue, however, is not one of them. File this one under -- "how could they possibly have missed that"??
doesn't happen here...on 4.0
LOL. There are a million and one things I can understand slipping through the "Alpha" test phase. This particular issue, however, is not one of them. File this one under -- "how could they possibly have missed that"??
I had to LOL too, John.
The possibilities are endless, the more one thinks about it, but as I suggested earlier, my brain's already morphed into mush, so I'm leavin' this tech fest to the young-ins who seem to be full of beans since 4.0's landing on planet Kemper...
I don't recall it happening on 4.0 either....going back to 4.0 until that's straightened out. Got a gig this weekend!
Edit: It seems the issue is there in 4.0 now...wasn't before.
Hi Mr. Sambora, if you sent a bug report via support adress on the main website, you receive a message by mail. Attache your backup in your answering mail..
Cheers
Frank
Yup, already been sorted out and is being worked on
Now I can't get rid of the damned morphed values.
Well, actually (as boring and painful as it may sound) you currently can (shall) look for any single parameter, and edit it until the "M" goes away. Basically you morph a set of parameters with itself...
Today page is gone.:-) !!!???
Do you by any chance use a Remote? There are pages that are not shown when the Remote is not connected.
FYI, the new update does not address the muting of the output signal when switching to tuner via midi.