How do you set INPUT correct???
![](https://forum.kemper-amps.com/wbb/images/avatars/97/3364-9705522c1569ed61d744a7468daa7d33104ffb06.jpg)
Input profiler stage
-
josip js -
April 3, 2020 at 2:41 PM -
Thread is marked as Resolved.
-
-
See here:
External Content www.youtube.comContent embedded from external sources will not be displayed without your consent.Through the activation of external content, you agree that personal data may be transferred to third party platforms. We have provided more information on this in our privacy policy. -
that depends on your definition of “correct” ?
if it sounds good it is good. Fortunately the KPA input is very forgiving. -
that depends on your definition of “correct” ?
if it sounds good it is good. Fortunately the KPA input is very forgiving.Haha, Which is good under normal circumstances. ???♂️
-
What are you trying to get "correct"? Level, noise gate, distortion v clean balance etc?
-
What are you trying to get "correct"? Level, noise gate, distortion v clean balance etc?
I would like an explanation for all this.
Clean is good and I'm happy with it, but I think distortion should sound a lot better.
-
Input Noise gate is a general noise reduction on the input signal for removing guitar noise rather than a traditional noise gate. I would set it as low as you can get away with. I am not a super high gain player so mine is rarely about 2 or 3 but others may use it differently.
QuoteKEMPER PROFILER Main Manual 7.0
This knob controls the Noise Gate, which eliminates the noise and hum of your guitar in a very smart way. Turn the NOISE GATE knob to the right until noise and hum have disappeared; do not turn it beyond that point, as this might alter the sound of your guitar. When set to the appropriate position, you will notice that noise and hum are eliminated, even when the strings are still sounding. There is no need for an additional release control as found in classic noise gates. The Noise Gate settings can be stored as part of a Rig.
Like "Clean Sens", the Noise Gate setting is part of the Input Section and is stored with the Rig. It is also stored as part of any input preset. When the Input Section is locked, the noise gate is locked as well.
There isn't a dedicated input gain to control what hits the AD converters but Clean Sense has an effect on this. Fortunately, the KPA input is quite forgiving so you don't need to get too obsessive about input level.
The main use of Clean Sense is as a global balance between clean and distorted sounds. If clean sounds are all too loud compared to distorted sounds reduce Clean Sense. If too quiet increase Clean Sense. Kemper say that most situations it should be set at 0 however, all of my guitars seem to sound way too loud on clean profiles so I usually run mine around -7db. The correct setting for one person won't be the correct one for someone else. In fact the correct setting may vary from guitar to guitar. You can set it once and lock it or set a different value for each rig/performance if you change guitars a lot.
QuoteKEMPER PROFILER Main Manual 7.0
Press this button to enter the Input Section. Here, you can set the input sensitivity and select the physical input for your guitar signal. In Browser Mode, the Input Section is locked by default. This means that the settings will be applied to every Rig, unless you decide to unlock it. If you do unlock this section, the input settings will be recalled individually with each Rig. In Performance Mode, the Input Section is not locked by default, because most users prepare and store their Performances with specific settings of the Input Section for particular songs and guitars. TheNoise Gate, with its dedicated knob, also belongs to the Input Section.
Front Panel Controls Head, PowerHead, Rack, and PowerRack 28
Clean Sens
Different types of guitars produce different output levels depending on their pickups and string gauge: for example, humbucker pickups generate higher voltages compared to single coils, and active guitars generate even hotter signal levels. If you feel that clean sounds are either very loud or very soft compared to distorted sounds, you can adjust Clean Sens to a level where clean sounds have the same perceived loudness as distorted sounds. Clean Sens determines the volume of clean sounds, but not the way that the amp or the effects are driven. A guitar with low output level stays cleaner; a hot guitar will still distort more easily.
Extremely “hot” guitars can generate unwanted distortion, indicated by the INPUT LED flashing red. This is only relevant for clean sounds, however - prominent amp distortion will completely mask a subtle clipping of the input.
Distortion sense is a global adjustment for distrotion. It doesn't affect level but compensates the gain within a profile for guitars with unsually loud or quiet pickups. This is usually set to 0 but can be adjusted to taste if required. It is intended as a means of matching a guitar to the profiler so is really a global setting not a something you would adjust on a rig by rig basis (unless you are changing guitars and they have wildly different output pickups).
QuoteKEMPER PROFILER Main Manual 7.0
Distortion Sens
Distortion Sens should normally stay at zero (middle) position. Every Rig will react as if you had connected yourguitar to the original amplifier.
If you feel that your guitar tends to drive the distortion too hot (or too soft) for most of your Rigs, then calibrate your guitar by adjusting Distortion Sens accordingly.
✓Clean Sens is not a simple input gain; you will notice that it does not affect the gain of a distorted sound. Distortion Sense is also not a simple booster, as it does not affect the gain of clean sounds. Neither of these parameters colors the sound.
✓A tutorial video about the Input Section and how to adjust Clean and Distortion Sens can be found on:http://www.kemper-amps.com/video
The parameters Input Source and Reamp Sense are global and are explained in the Instrument Input and Reampingchapter.
I really is a suck it and see menu that is best set with your ears rather than logic or preconcieved "correct" V "wrong".
-
Input Noise gate is a general noise reduction on the input signal for removing guitar noise rather than a traditional noise gate. I would set it as low as you can get away with. I am not a super high gain player so mine is rarely about 2 or 3 but others may use it differently.
There isn't a dedicated input gain to control what hits the AD converters but Clean Sense has an effect on this. Fortunately, the KPA input is quite forgiving so you don't need to get too obsessive about input level.
The main use of Clean Sense is as a global balance between clean and distorted sounds. If clean sounds are all too loud compared to distorted sounds reduce Clean Sense. If too quiet increase Clean Sense. Kemper say that most situations it should be set at 0 however, all of my guitars seem to sound way too loud on clean profiles so I usually run mine around -7db. The correct setting for one person won't be the correct one for someone else. In fact the correct setting may vary from guitar to guitar. You can set it once and lock it or set a different value for each rig/performance if you change guitars a lot.
Distortion sense is a global adjustment for distrotion. It doesn't affect level but compensates the gain within a profile for guitars with unsually loud or quiet pickups. This is usually set to 0 but can be adjusted to taste if required. It is intended as a means of matching a guitar to the profiler so is really a global setting not a something you would adjust on a rig by rig basis (unless you are changing guitars and they have wildly different output pickups).
I really is a suck it and see menu that is best set with your ears rather than logic or preconcieved "correct" V "wrong".
Great explanation, thanks a lot! ??