Hi, I want to send MIDI to my Whammy 4 using my Profiler Remote and BOSS FV500H, is it possible?
If so, how can i set it up?
Hi, I want to send MIDI to my Whammy 4 using my Profiler Remote and BOSS FV500H, is it possible?
If so, how can i set it up?
Yes you can :
QuoteThe Whammy uses MIDI Program Change commands for effect selection. Effects can be selected in either an active or bypassed state. The following illustrations show the MIDI Program Change mappings for Classic mode and Chords mode.Effects MIDI Program Change Mapping (Classic Mode)When set to Classic mode, the following illustration outlines the Program Change commands recognized by the Whammy and the corresponding effect setting and its status.
MIDI CC messages can then be used to control the Whammy Expression Pedal position.
MIDI Continuous Control Using MIDI continuous control commands, the Whammy’s Expression Pedal position can be remotely controlled. MIDI CC11 adjusts the Expression Pedal position. A value of 0 on MIDI CC11 corresponds to a toe up position and a value of 127 corresponds to a toe down position.
https://www.digitech.com/on/demandware.…hammy_OM_EN.pdf
Whammy 4 manual : https://www.manualslib.com/manual/380879/…?page=13#manual
Sending PC (changing slots in performance mode ) from KPA will turn on/off desired function on the whammy. Just set PC number on the desired slot in performance mode in KPA .
You can use Pedals to MIDI feature to send CC11 message (morph in KPA) to controll whammy pedal position.
http://hmon.ir/digitech/whamm…vaVbcoYFszLgJH4
This is a really cool thing for getting the midi numbers for the Whammy/Whammy DT. Even has a setting for midi offset.
Yes you can :
https://www.digitech.com/on/demandware.…hammy_OM_EN.pdf
Whammy 4 manual : https://www.manualslib.com/manual/380879/…?page=13#manual
Sending PC (changing slots in performance mode ) from KPA will turn on/off desired function on the whammy. Just set PC number on the desired slot in performance mode in KPA .
You can use Pedals to MIDI feature to send CC11 message (morph in KPA) to controll whammy pedal position.
This is weird because i use it in the same patch as something that has Morph, is anything to be done? D:
rafaeldamage just use whammy exp pedal and do not activate Pedal to MIDI function.
rafaeldamage just use whammy exp pedal and do not activate Pedal to MIDI function.
i need to control whammy deom stage because my kemper will be behind monitor console, so the only thing in stage is my remote via ethernet.
LETS TRY!
I've been controlling the Whammy via PC mapping from a Mooer GE300 controlling my Kemper. I'm thinking of re-organising my rig and going Dual Kemper, anybody know if I can use CC data from the Whammy to control Kemper Wah modules?
I've been controlling the Whammy via PC mapping from a Mooer GE300 controlling my Kemper. I'm thinking of re-organising my rig and going Dual Kemper, anybody know if I can use CC data from the Whammy to control Kemper Wah modules?
The Whammy won't output any midi data I'm afraid.
But the way you're controlling your Whammy is cool. I control mine (preset and expression) via midi from my helix. The pedal lives in a rack drawer.
The Whammy won't output any midi data I'm afraid.
But the way you're controlling your Whammy is cool. I control mine (preset and expression) via midi from my helix. The pedal lives in a rack drawer.
Damn, imagine being able to leave the expression pedal behind and just use the whammy for everything, would be so simple. PC in for tuning changes, CC out for all expression.
The Mooer as a controller almost works perfectly , so I have a permanent onstage back-up that's just a little bigger than a remote. The problem is.......lack of CC out