Hi,
anyone has a tipp for a case or bag for the remote + 2 Exp Pedals (EP 1)?
Close to 70cm wide and about 26cm "deep"?
What are you using?
Martin
Hi,
anyone has a tipp for a case or bag for the remote + 2 Exp Pedals (EP 1)?
Close to 70cm wide and about 26cm "deep"?
What are you using?
Martin
I bought a custom case from a local manufacturer.
Fits very nicely.
I also heard that thomann sells a case for a line 6 pod which fits for the remote plus 2 exp pedals.
I think Ingolf uses this one.
I bought a custom case from a local manufacturer.
Fits very nicely.I also heard that thomann sells a case for a line 6 pod which fits for the remote plus 2 exp pedals.
I think Ingolf uses this one.
I'm using exactly this one:
https://www.thomann.de/de/thon_case_f…se+fbv_193333_0
Ha!
I thought I looked at EVERY Thon-Case for these floor-units - but must have overlooked this one.
should fit pefectly!
thanks
Martin
Check out also Grosse Cases, based in Germany: http://grosse-cases.com/epages/ed3797e…gories/54/28/35
They're building custom cases on demand with the exact mesurements. I own one for my Diezel head and for my stompboxes. They're built like a tank and if you remove the cover of the pedalboard, only the floorboard - which is completely flat - remains on the stage (there's no border).
Currently using this board. Works great and you can get a hard shell or soft shell case.
I just picked up a Pelican 1610 case for my KPA Toaster + Remote + Exp Pedals/Cables. Since you don't have the Remote you'd have plenty of room for extra cables or tossing in a drive pedal or two if you ever felt like it.
I just picked up a Pelican 1610 case for my KPA Toaster + Remote + Exp Pedals/Cables. Since you don't have the Remote you'd have plenty of room for extra cables or tossing in a drive pedal or two if you ever felt like it.
Looks great mate
I just picked up a Pelican 1610 case for my KPA Toaster + Remote + Exp Pedals/Cables. Since you don't have the Remote you'd have plenty of room for extra cables or tossing in a drive pedal or two if you ever felt like it.
How much does that whole thing weigh then? I've been considering a Pelican case for my setup, exactly the way you have it in your photo! Is that a single expression pedal in there?
Hey @jeffmn, I haven't had a chance to weigh mine but @lonestargtr had a similar setup with the same Pelican 1610, KPA, Remote, and Exp pedal (I think) and it came in just under 50 lbs with cables and everything.
I can confirm 49.5lb with everything. Can't beat it. Best rig.
Bought a case for my HD500 from a fellow making them on eBay a number of years back (my pre-Kemper days). Ended up working great for the Kemper Remote setup as well.
Pelican is really nice, but i think it's 31lbs according to their website. Just too heavy for me.
This is how I do it. It works well for me. Less weight than a pedal board and I can use only what I need at the time.
Thought i will share, what i got:
It´s a custom "thon"-case:
The 76cm version of AmARHyll from Emma Electronics works fine. €168 from Thomann. A 66-68cm board would strictly be enough, but I prefer a few cm extra space between the remote and exp-pedals.
I ordered: 66cm x 26cm x 8cm.
but now as i have it here - 66 x 24 x 7 would be enough
it was 159,- Euros
I ordered: 66cm x 26cm x 8cm.
but now as i have it here - 66 x 24 x 7 would be enough
it was 159,- Euros
I was looking into speccing a custom case and took your dimensions as a base, but how did you get it to be only 8 high? Least I can do is 13cm high.
My dimensions are inside the Case... thats what i had to give them when ordering. Outside is more (don´t know exactly, i don´t have it here right now)
Martin
My dimensions are inside the Case... thats what i had to give them when ordering. Outside is more (don´t know exactly, i don´t have it here right now)
Martin
Yeah, lowest I can go with their case builder is 13 inside. Doesn't matter though, 13 is fine with me.