I've found that about a 4db boost works good for solos. Also with some of the gainer stuff I might boost the mids a bit. Let us know how it went.
Posts by teleplayer364
-
-
Trying to find the SW 22 profile on the rig exchange with zero luck. I've searched under morgan lee, Danishpete and a few other versions of these. Can anyone help out? Thanks!
-
I also use a lot of the MBritt profiles and they just work in the mix. I made the mistake of using headphones to tweak my profiles. Much better to tweak them w/ monitors. I also started with guitar cabs but found to get the best tone out front the FRFR route worked better for me. I use the DXR10's after trying a few different setups. This ended up working the best because what I'm getting out of the monitors is really close to what is coming out of FOH. I did some dialing in on the FOH with guitar cabs, but it was trickier and less consistent. Easier for me using monitors that are similar to FOH. Of course YMMV.
-
Finally had a chance to check them out. Found two that are really nice. A fine example of a traditional Fender clean and slightly pushed. Thanks for sharing them.
-
When it happens again I guess I will record it and open a support ticket. Seems as only one other person has had this problem it must be a problem with the unit.
-
Thanks Ronald V. I will look into this.
-
Thanks for the reply. When I unplugged the Kemper from the monitors they were dead quiet. when I plugged them back in it came back or got a little worse. Everything was plugged into the same power strip. Just curious if anyone else has had this problem.
-
Set up for a bar gig last night. when I powered up my DXR10s and Kemper there was a high pitch ringing,the volume was not really loud but present. powered down the kemper and the pitch got lower and a little louder. I had this happen one other time. I did lift the ground to the monitors and it got better. Wondering if a good rf filter would have helped this. Didn't see any neon signs in the bar. Anyone else have similar issues and found a good solution? Otherwise the kemper sounded awesome! Thanks.
-
Solved, I wasn't putting the files in the shared folder on the USB stick, just loading onto the stick. I had to reload the stick and open it , then move the file over to the shared folder then load it into the Kemper. Yeah these delays are a game changer! Thanks everyone for your help. I try hard to figure stuff out on my own, but it's great to have this forum and all your help when I get stuck.
-
I have all the new delays, just not the demonstration presets. Used both the browse and type knob and scrolled thru the delays but no presets.
-
-
Hi, as the subject line states I've can't find the the new demonstration delay presets now that I've loaded 5.0 on my profiler. I see and can edit the new delays on it, but can't get to the presets. I read the addendum for the new delays but no luck. Tried to just add the presets with the memory stick and the profiler stated they are already on it.Please help a technically challenged brother out!
-
Hello all. Been working on performance programming. I like using the copy paste option for moving rigs to different slots and performances. Once I copy and paste the rig the paste button stays lit and seems I can't copy and paste another performance after that. Looked in the manual and found nothing. Been getting better at using the features on this amazing unit but every once in a while I get hung up. Thanks in advance.
-
Hello all. Been working on performance programming. I like using the copy paste option for moving rigs to different slots and performances. Once I copy and paste the rig the paste button stays lit and seems I can't copy and paste another performance after that. Looked in the manual and found nothing. Been getting better at using the features on this amazing unit but every once in a while I get hung up. Thanks in advance.
-
Yes...........................................................No, just tried it again and found the error in my ways. Thanks for helping. I'm hoping to master this thing, but seems to occasionally get the best of me.
-
I'm trying to move my performances in RM for set list changes. I used to just click and drag the performances to the spot I wanted them but now it's not working. Haven't tried this since I went to 4.06. I have the latest revision of RM. I'm able to do it directly on the Kemper. Any thoughts?
-
I'm curious about what speaker they use in their cabinet. Anyone?
-
-
It is one of the Kemper Factory rigs that are included when you buy a KPA.
If you no longer have them, you can download the Factory Rig Pack from Kemper-amps.com
I should have it then, Thanks.
-
rmpacheco Morgan AC20
If only one. I'd go with this.