Is using an EMG SA in the middle too obvious of a suggestion?
That's not the question. It's getting the configuration right when there are no standard HSH sets, and all the HH sets only come with a 2-pickup bus. There's probably a decent accessory set I'm missing.
So I’m struggling - trying to figure out the best way to get an EMG set (probably 57/66TW) and adding in a single coil for my middle pickup. Both sets come with a 2 pickup bus, and obviously 57/66 with a push pull - anyone had any experience of this with a 5 way switch too?
Has anyone else had more issues with Floyd Roses than with Ibanez edge systems?
It comes as something when the most stable trem system I have is an Ibanez Edge 3.
Anyone got any tips or things they use to help with tuning stability having used the bar at all?
Look at the "Rig Packs" on the online Downloads page, and/or in Rig Manager:
https://www.kemper-amps.com/downloads/10/Rig-Packs
KEMPER Rig Pack 01, 02 & 04 (April 2012 - January 2013)
KEMPER Legacy Rig Packs 2012 (July 2013), 2013 (July 2014), 2015 (March 2016), & 2017 (April 2018)
These are already in my rig manager and there are loads that don't show up, wouldn't have thought any of the rigs would be regionalised or anything either.
After a bit of random googling I've come across various manuals for the Kemper showing a lot more variation in available rigs such as handwired JCM800s, more signature amps such as the Blackstar Blackfire 200 Gus G model etc. Anyone know where these rigs went to?
Morning all, (UK time).
Has anyone ever tried recording bass using a guitar plus digitech whammy using the drop tuning settings through a bass profile?
Wondered if it sounded anywhere near decent or at least doable with post-processing?
Ta
From his recent Twitch streams, he's profiled his old Rocktron Prophesy tones, and original JMP-1 tones. Unfortunately there's nothing from looking at his rig manager that gives anything away, other than knowing the Prophesy tone is from the Mega Drive channel.
I'd also want a decent modern DF tone for anyone who might have one going!
The thing i keep seeing here is that the Kabinet is to be connected to the monitor output, but as a cab shouldn't this primarily be the speaker output (i.e. like a normal cab)? Surely the Kone IRs can be used on speaker output mode too for all profile types.
Lots of conflicting information and nothing concrete to say it can be used in that way when also recording through S/PDIF etc. also.
Hi there - no, the Kemper does one rig at a time, but...
If you record your raw guitar to another track you can reamp that back through the Kemper to achieve the same thing. In fact you can take several copies and use a different rig for each.
Fender in the left, Marshall in the right and Vox in the middle, no problem. ?
Fab thanks!
In the interests of consistency and time, I was wondering if there is a way to record say two tracks simultaneously with different rigs into ProTools at the same time.
For Example as a double rhythm track mimicking two guitarists, pro/live sound etc?
Thanks, Nathaniel 
usually, a decent audio interface will have what they call zero-latency monitoring, where the input signal is routed directly to the outputs with the monitors.
the round-trip through the DAW & plugins is what causes high latencies.
So direct through s/pdif to essentially pc speakers as monitors is as good as using the cab at the same time.
I know I'm bumping this from beyond its forum grave but, assuming from what being said that (having not yet tried it), Kemper -> Cab plus s/pdif -> interface for recording. Using Cab as the sound source as it is definitely delay free.
Or would using the computers speakers be as delay free? Handy to use a cab essentially as a monitor right?
The sound quality is the same though all of them, so it's up to you. I have many ins/outs on my interface, so use the 2 xlr main outs to record in stereo if I want (you can do the same with the 1/4" outs) usually mono though, the direct out runs the clean guitar signal for possible re-amping later.
Unusual part of my setup:
My unit is just used for recording (never leaves) so I also have one set of the outputs from the interface goes to the alternate input and return input on the Kemper. When recording I can have tons of plugins running in my DAW at max buffer size, and no issues with latency because it's all monitored on the Kemper, you can hear the DAW playback and your live guitar. (which can be panned in the rig menu).
Alternate approach would be to monitor direct from the audio interface. Pretty much every interface should have this ability in one form or another- either with driver software or onboard knob. Record monitoring in your DAW can be problematic if you're running many plugins (or have an old computer like me), you get glitches unless the buffer size is increased, which causes latency delay.
Thanks for the response. In terms of recording through interface etc. I'm assuming I can still get the sound from the cab whilst I'm recording. (Very much a noob)!
I would consider getting an external audio interface for recording. There not all that expensive these days. As far as hooking everything up, the S/PDIF is only one option. There are many other output choices on the Kemper. Be aware that there is a measurable amount of latency using S/PDIF, possibility of stutters and pops, glitches, and no difference in sound quality. There's never any pops or glitches with the other outputs, lower latency (pretty much none), and sound quality is the same. (I never use S/PDIF after trying it, latency messes up with my playing a little)
Still, get an audio interface with sufficient inputs and try for yourself what works best.
Thanks for your response. In terms of the other outputs then, which would you prefer or consider first?
Just about to get my power head and had a question on linking to pc/recording, I’ve seen a few questions not answered exactly how I was anticipating.
Essentially I want to record directly to my pc from the kemper output, S/PDIF seems to be the preferred method, but is it just a case of getting a soundcard (internal or external) and linking from the kemper to that, to the pc?
Cheers
Nathaniel
